Do It Yourself Bathtub Installation.
Do It Yourself Bathtub Installation.
Blog Article
Do you find yourself looking for answers about A Step-by-Step Guide to Installing a Bathtub?
Installing a bathtub isn't exactly rocket science, however it does call for strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old bathtub with a new one is also a moderately difficult project. If the old tub is readily available, the project can move quickly; if you have to open a wall to remove the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either situation, the job is within a house handyman's skills, although you will need a helper to move out the old tub and also embeded in the brand-new one. Make certain you have actually qualified yourself for the job and fit trying it. As opposed to employing a specialist to take over a halfway-completed project, it is better to take into consideration using one prior to you begin. Chances are you may require a professional plumber to make tube connections.
This write-up will certainly assist you set up a new bath tub in your washroom if you have actually already bought a brand-new bathtub as well as do not require to alter the arrangement of your previous water pipelines.
Your tools and product list ought to comprise the following:
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installation, after that the first thing you must do is disconnect the water supply. After doing so, switch on the taps to drain pipes any type of water remaining in the system. The procedure of eliminating the existing taps can be fairly problematic as a result of the limited access that is usually the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly come from the pipelines. Once the supply pipelines have been gotten rid of, make use of the very same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming during this process. As soon as the taps have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any old securing substance.
Before going on to fit the new faucets, compare the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Touches
If the tails of the new faucets are plastic, then you will certainly require a plastic port to prevent damages to the thread. One end of the port fits on the plastic tail of the faucet and the various other end gives a connection to the current supply pipes.
If you require to fit a monobloc, after that you will certainly require minimizing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the faucet in the mounting opening in the bath/basin making certain that the washers remain in area between the tap and also the sink. Safeguard the tap in place with the supplier provided backnut. When the faucet is firmly in place, the supply pipes can be linked to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular faucet connectors. The former kind needs to be attached to the tap ends initially, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Installing the Tub
Utilizing both wood boards under its feet, position the bathtub in the required setting. The wood boards are practical in equally spreading the weight of the bathtub over the area of the boards rather than focusing all the weight onto 4 tiny factors.
The following objective is to make certain that the bathtub is leveled all round. This can be achieved by checking the spirit level as well as changing the feet on the tub up until the level reviews degree.
To mount faucets, fit all-time low of the outermost adaptable faucet adapter to the ideal supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Activate the water supply and examine all joints and brand-new pipework for leakages and also tighten them if essential. Load the bath tub as well as additionally examine the overflow electrical outlet and also the normal outlet for leaks.
Lastly, fix the bath paneling as defined in the maker's user's manual. Tiling and also securing around the bath tub needs to wait till the bath tub has actually been made use of at the very least when as this will certainly resolve it right into its last setting.
Getting ready for the Setup
First of all, the sustaining framework supplied with the bath ought to be fitted (if required) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to ensure that if the tap comes with a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the taps device to stop stress on the bathtub.
Fit the adaptable faucet connectors to the bottom of both faucets using 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet through the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. See to it you utilize all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath must now prepare to be fitted in its last position.
Tiling Around the Tub
In the area where the bathroom fulfills the tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to split a rigid seal, triggering the water to pass through the wall in between the bath as well as the tiling, leading to issues with wetness as well as feasible leaks to the ceiling below.
You can pick from a variety of coloured sealers to assimilate your fixtures and also fittings. They are offered in tubes and also cartridges, and are capable of sealing voids up to a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of soaked paper or soft rope. Bear in mind to always fill up the bath tub with water before securing, to allow for the motion experienced when the bathtub is in use. The sealer can fracture fairly early if you do not think about this movement before securing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily available on the market. It is advisable to fit the tiles using water-resistant or waterproof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you like reading about Tools You Need to Install a New Bathtub ? Try leaving a comment down the page. We would be pleased to know your reactions about this article. We hope that you come back again later on. Remember to take a moment to distribute this post if you enjoyed reading it. Thanks for your time. Kindly come by our website back soon.
Get Offer Report this page