HOW TO REPLACE A TUB IN YOUR BATHROOM

How to Replace a Tub in Your Bathroom

How to Replace a Tub in Your Bathroom

Blog Article

Contact Us

Do you find yourself trying to locate tips about A Step-by-Step Guide to Installing a Bathtub?


How to Install a Bathtub
Setting up a bath tub isn't exactly rocket science, however it does call for strong plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old bathtub with a brand-new one is likewise a reasonably difficult project. If the old tub is easily available, the project can move quickly; if you have to open up a wall surface to remove the old tub and position the new bathtub, the task is much harder. In either case, the project is within a home handyman's skills, although you will need a helper to move out the old tub and set in the brand-new one. Make sure you have actually certified on your own for the task as well as are comfortable attempting it. Instead of hiring a contractor to take over a halfway-completed task, it is far better to take into consideration using one prior to you start. Possibilities are you might require a specialist plumber to make tube links.
This post will help you install a brand-new bath tub in your washroom if you have currently bought a brand-new tub and also don't require to alter the arrangement of your previous water system pipes.
Your devices and material list must comprise the following:
  • New Bath tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipeline Caps


  • Getting ready for the Installation


    To start with, the supporting frame provided with the bath needs to be fitted (if needed) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the tub. When suitable the tap block, it is important to make certain that if the tap comes with a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps device to avoid pressure on the tub.
    Fit the adaptable tap adapters to the bottom of the two faucets using 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you make use of all of the provided washers.
    Link the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath ought to currently prepare to be fitted in its final placement.

    Removing Old Taps


    If you need to change old faucets with new ones as a part of your installation, after that the first thing you need to do is separate the supply of water. After doing so, switch on the faucets to drain any water staying in the system. The procedure of getting rid of the existing taps can be rather troublesome as a result of the restricted access that is typically the instance.
    Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the taps. Have a cloth ready for the staying water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been removed, make use of the very same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from transforming throughout this procedure. As soon as the faucets have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any kind of old securing substance.
    Prior to going on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.

    Mounting the Bath tub


    Making use of both wood boards under its feet, place the bath tub in the called for setting. The wood boards are valuable in evenly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto four tiny points.
    The following goal is to ensure that the bathtub is leveled all round. This can be attained by inspecting the spirit level and also changing the feet on the bathtub till the spirit level reads degree.
    To install faucets, fit the bottom of the furthest adaptable tap adapter to the proper supply pipe by making a compression sign up with; then do the very same for the other faucet.
    Turn on the water supply and examine all joints and brand-new pipework for leaks and also tighten them if needed. Fill the tub and likewise check the overflow electrical outlet and the regular outlet for leakages.
    Finally, take care of the bath paneling as defined in the producer's user's manual. Tiling and securing around the bathtub must wait until the tub has actually been utilized at the very least once as this will certainly settle it right into its last position.

    Suitable New Taps


    If the tails of the new faucets are plastic, then you will certainly require a plastic connector to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end gives a connection to the current supply pipes.
    If you require to fit a monobloc, then you will certainly require decreasing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
    Next, place the tap in the placing hole in the bath/basin ensuring that the washers remain in location between the tap as well as the sink. Secure the faucet in place with the maker provided backnut. When the faucet is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The previous type must be connected to the faucet finishes initially, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.

    Tiling Around the Bathtub


    In the location where the bath satisfies the tile, it is required to secure the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to crack a stiff seal, creating the water to penetrate the wall surface in between the bath and also the tiling, leading to issues with wetness and feasible leaks to the ceiling listed below.
    You can choose from a range of coloured sealers to assimilate your fixtures as well as installations. They are sold in tubes as well as cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of drenched paper or soft rope. Remember to always fill up the bath tub with water before sealing, to enable the motion experienced when the bathtub remains in usage. The sealer can fracture fairly early if you do not consider this motion before sealing.
    Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise quickly offered on the marketplace. It is a good idea to fit the floor tiles making use of waterproof or water-proof sticky as well as grout.

    Bathtub Installation


    How Important Is A Bathtub To Your Home?


    High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.


    Install Piping Before Tub


    You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.


    Position the Tub


    Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.



    NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.


    Assemble Drain Connections


    Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.


    Place a Pipe For the Shower Head


    First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.


    Attaching Hot and Cold Water Lines


    Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.


    Install the Spout


    Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.



    NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.


    Check For Leaks


    Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.


    estore the Bathroom Wall


    Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

    https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    I hope you enjoyed our post on A Step-by-Step Guide to Installing a Bathtub. Thanks for taking time to read our short article. In case you enjoyed our page if you please remember to pass it around. We treasure reading our article about Tools You Need to Install a New Bathtub .



    Visit Homepage

    Report this page